MS Supplies for Mass Spectrometry Systems

MS Supplies

20 Produits

MSD Source Nut, pk.2

Restek MSD Source Nut, pk.21.2 mm nut bore permits easy removal of ferrules with a standard tapered-needle file (cat.# 20106). Made of brass to prevent thread stripping on the transfer line. Design enhances ease of threading onto the transfer line and improves overall lifetime.

Art.-Nr.: RT-20643

EUR 38.00

Disponible

EZ No-Vent Transfer Line, Replacement deactivated transfer line 100um: 3 feet

Restek EZ No-Vent Transfer Line, Replacement deactivated transfer line 100um: 3 feet

Art.-Nr.: RT-21018

Demande de prix

En cours de réapprovisionnement

MSD Conversion Fitting, Ring Seal, pk.2

Restek MSD Conversion Fitting, Ring Seal, pk.2

Art.-Nr.: RT-21313

EUR 23.00

En cours de réapprovisionnement

MSD Conversion Fitting, ea.

Restek MSD Conversion Fitting. A flat, soft aluminum sealing ring deforms and butt-seals against the MSD interface. A standard Vespel ferrule seals the column and 1/16-inch stainless steel nut. Fitting is constructed of nickel-plated brass for longevity and softness. Use any standard Vespel or Vespel/graphite 1/16-inch ferrule. Includes a 1/16-inch stainless steel nut and two replacement sealing rings. Order Vespel/graphite ferrules separately. Improved design reduces chance of leaks.

Art.-Nr.: RT-21314

EUR 67.00

En cours de réapprovisionnement

EZ No-Vent for Agilent 5971, 5972, 5973 or 5975 MS

Restek EZ No-Vent for Agilent 5971, 5972, 5973 or 5975 MS. Restek designed the EZ No-Vent GC column-mass spectrometer connector to be simple and easy to use. A critical orifice in the EZ No-Vent connector minimizes the amount of oxygen allowed into the MS source, eliminating the need for purge gas as is required for other manufacturers' vent systems. This enables you to skip the lengthy vent and pump-down cycle otherwise required when you make a column change, saving nearly a day of downtime with each column change. The EZ No-Vent connector easily attaches to the MS source without special tools or extra plumbing.

Art.-Nr.: RT-21323

EUR 280.00

En cours de réapprovisionnement

Installation Gauge, capillary installation gauge for Agilent 5973/5975 MS

Restek Installation Gauge, capillary installation gauge for Agilent 5973/5975 MS. Seats ferrules onto column for consistent installations. Made from high-quality stainless steel. Note: Do not use on a 5975/5977 MS with an EI source (inert or SS). Doing so will extend the column too far into the ion source. This installation gauge is compatible with the 5975 MS with a CI source and the 5977 MS with the extractor or high-efficiency sources.

Art.-Nr.: RT-21894

EUR 247.00

En cours de réapprovisionnement

Transfer Line Reducing Kit for Thermo TRACE and Focus DSQ Mass Spectrometers

Restek Transfer Line Reducing Kit for Thermo TRACE and Focus DSQ Mass Spectrometers

Art.-Nr.: RT-22082

EUR 62.00

En cours de réapprovisionnement

EZ No-Vent for Bruker/Varian Saturn 2000 Series MS

Restek EZ No-Vent for Bruker/Varian Saturn 2000 Series MSWe designed the EZ No-Vent GC column-mass spectrometer connector to be simple and easy to use. A critical orifice in the EZ No-Vent connector minimizes the amount of oxygen allowed into the MS source, eliminating the need for purge gas as is required for other manufacturers' vent systems. This enables you to skip the lengthy vent and pump-down cycle otherwise required when you make a column change, saving nearly a day of downtime with each column change. The EZ No-Vent connector easily attaches to the MS source without special tools or extra plumbing.

Art.-Nr.: RT-22423

Demande de prix

En cours de réapprovisionnement

EZ No-Vent for GC/MS - Shimadzu QP 2010 & QP 2010 Plus, kit

Restek EZ No-Vent for GC/MS - Shimadzu QP 2010 & QP 2010 Plus, kit. Restek has designed the EZ No-Vent GC column-mass spectrometer connector to be simple and easy to use. A critical orifice in the EZ No-Vent connector minimizes the amount of oxygen allowed into the MS source, eliminating the need for purge gas as is required for other manufacturer's vent systems. The lengthy vent and pump-down cycle is not required, and normal instrument down-time from a column change is dramatically reduced. The EZ No-Vent connector easily attaches to the MS source without special tools or extra plumbing.

Art.-Nr.: RT-22431

EUR 364.00

En cours de réapprovisionnement

EZ No-Vent for Thermo Scientific Focus DSQ GC Series MS

Restek EZ No-Vent for Thermo Scientific Focus DSQ GC Series MSRestek designed the EZ No-Vent GC column-mass spectrometer connector to be simple and easy to use. A critical orifice in the EZ No-Vent connector minimizes the amount of oxygen allowed into the MS source, eliminating the need for purge gas as is required for other manufacturers' vent systems. This enables you to skip the lengthy vent and pump-down cycle otherwise required when you make a column change, saving nearly a day of downtime with each column change. The EZ No-Vent connector easily attaches to the MS source without special tools or extra plumbing.

Art.-Nr.: RT-22454

EUR 331.00

En cours de réapprovisionnement

Ion Source Cleaning Powder- Aluminum Oxide Powder for cleaning Mass Spec parts, 1kg

Restek Ion Source Cleaning Powder- Aluminum Oxide Powder for cleaning Mass Spec parts, 1kgUse this aluminum oxide powder to clean surfaces that contact the sample or ion beam when you encounter poor sensitivity and inadequate abundances at high masses.

Art.-Nr.: RT-22685

EUR 59.00

En cours de réapprovisionnement

Pump Oil, Rough Pump Oil for MSD Pumps, 1 liter

Restek Pump Oil, Rough Pump Oil for MSD Pumps, 1 literFormulated from crude oil stocks known for their durability and line-lubricating qualities. Use in Agilent 5973/5972/5971 and GCD mass spec systems, or in other manufacturers’ MSD systems that require rough pump oil. Under average use, the oil in the foreline rough pump should be replaced every six months.

Art.-Nr.: RT-22687

EUR 55.00

En cours de réapprovisionnement

ETP Electron Multiplier For Agilent 5973 & 5975 GC-MS (not for 5975C Triple Axis Detector, includes

Restek ETP Electron Multiplier For Agilent 5973 & 5975 GC-MS (not for 5975C Triple Axis Detector, includes mount for initial installation)Optimized ion and electronic optics for maximum performance.Increased surface area for enhanced sensitivity and extended operational life.The multi-dynode approach of all ETP electron multipliers results in longer lifetimes—and better sensitivity—compared with channel electron multipliers (CEM) or continuous-dynode multipliers.The electron multipliers manufactured by ETP use a proprietary dynode material. This material has a number of properties that make it very suitable for use in an electron multiplier. It has very high secondary electron emission, which allows exceptional gain to be achieved from each dynode. This material is also very stable in air. In fact, an ETP multiplier can be stored for years before being used. As a direct result of the high stability of the active materials used in ETP multipliers, they come with a two-year shelf life warranty (stored in original, sealed package). Many testing laboratories take advantage of this long shelf life by keeping a replacement ETP multiplier on hand, ready for immediate installation. This keeps instrument downtime to a minimum.For a typical ETP electron multiplier for GC-MS, the total active dynode surface area is ~1000 mm2. This can be compared to a standard continuous dynode multiplier that has a total channel surface area of only around 160 mm2 (for a channel with 1 mm diameter and 50 mm length). This increased surface area spreads out the workload of the electron multiplication process over a larger area, effectively slowing the aging process and improving operating life and gain stability.*Note: The electron multipliers have been specifically developed to retrofit the original manufacturer's equipment. The detector incorporates a modular design to facilitate ease of replacement and additional innovations intended to enhance performance. First-time installation requires a mount that includes the mechanical housing. After initial installation, only the replacement electron multiplier is required.†This unit is not designed for use with the 5975C Triple Axis Detector.

Art.-Nr.: RT-23074

EUR 3,765.00

En cours de réapprovisionnement

ETP Electron Multiplier For Agilent 5973 & 5975 GC-MS and LC-MSD (not for 5975C Triple Axis Detector

Restek ETP Electron Multiplier For Agilent 5973 & 5975 GC-MS and LC-MSD (not for 5975C Triple Axis Detector, Replacement Multiplier)Optimized ion and electronic optics for maximum performance.Increased surface area for enhanced sensitivity and extended operational life.The multi-dynode approach of all ETP electron multipliers results in longer lifetimes—and better sensitivity—compared with channel electron multipliers (CEM) or continuous-dynode multipliers.The electron multipliers manufactured by ETP use a proprietary dynode material. This material has a number of properties that make it very suitable for use in an electron multiplier. It has very high secondary electron emission, which allows exceptional gain to be achieved from each dynode. This material is also very stable in air. In fact, an ETP multiplier can be stored for years before being used. As a direct result of the high stability of the active materials used in ETP multipliers, they come with a two-year shelf life warranty (stored in original, sealed package). Many testing laboratories take advantage of this long shelf life by keeping a replacement ETP multiplier on hand, ready for immediate installation. This keeps instrument downtime to a minimum.For a typical ETP electron multiplier for GC-MS, the total active dynode surface area is ~1000 mm2. This can be compared to a standard continuous dynode multiplier that has a total channel surface area of only around 160 mm2 (for a channel with 1 mm diameter and 50 mm length). This increased surface area spreads out the workload of the electron multiplication process over a larger area, effectively slowing the aging process and improving operating life and gain stability.*Note: The electron multipliers have been specifically developed to retrofit the original manufacturer's equipment. The detector incorporates a modular design to facilitate ease of replacement and additional innovations intended to enhance performance. First-time installation requires a mount that includes the mechanical housing. After initial installation, only the replacement electron multiplier is required.†This unit is not designed for use with the 5975C Triple Axis Detector.

Art.-Nr.: RT-23075

EUR 2,981.00

En cours de réapprovisionnement

MS Interface Nut Brass (nickel plated), 1/16" x 1.2mm hole (extended), works with Thermo ISQ, 5-pk.

Restek MS Interface Nut Brass (nickel plated), 1/16" x 1.2mm hole (extended), works with Thermo ISQ, 5-pk.

Art.-Nr.: RT-23098

EUR 34.00

En cours de réapprovisionnement

High Temp. El Filament For Agilent GC-MS Similar to Agilent G7005-60061, ea.

Restek High Temperature El Filament For Agilent GC-MS Similar to Agilent G7005-60061. EI (electron ionization) filaments meet or exceed original manufacturer's performance. Every filament is subjected to QC tests, including heat, electrical current, and resistance. Samples from each filament manufacturing lot are installed in an MSD for in situ testing.

Art.-Nr.: RT-23099

EUR 210.00

Disponible

Gold Tip Transfer Line, ea.

Restek Gold Tip Transfer Line, ea.For use with Agilent 5971/5972 MS systems. Gold-plated for inertness. Meets or exceeds original manufacturer's performance.

Art.-Nr.: RT-24699

Demande de prix

En cours de réapprovisionnement

Inland 45 Rough Pump Oil for MS Pumps, 1 liter

Restek Inland 45 Rough Pump Oil for MS Pumps, 1 liter. Recommended for most mass spectrometers. Ease at cold start. Low vapor pressure 10-7 torr. Nontoxic and noncorrosive. Compatible with Buna-N, neoprene, and Viton seals. Optimum vacuum pump performance. Lowest mass spectrometer background. Recommended for optimum mass spec performance.

Art.-Nr.: RT-24819

EUR 131.00

En cours de réapprovisionnement

Mass Spec Cleaning Kit Without Dremel Tool

Restek Mass Spec Cleaning Kit (w/o Dremel Tool). Poor sensitivity, loss of sensitivity at high masses, or high multiplier gain during an auto-tune are all indicators that your mass spectrometer source may need to be cleaned. Restek has assembled all of the necessary components for cleaning and polishing your ion source.

Art.-Nr.: RT-27195

EUR 295.00

En cours de réapprovisionnement

Mass Spec Cleaning Kit Replacement Parts Kit (includes cloths, micro mesh sheets, small and large gl

Restek Mass Spec Cleaning Kit Replacement Parts Kit (includes cloths, micro mesh sheets, small and large gloves)

Art.-Nr.: RT-27196

EUR 96.00

En cours de réapprovisionnement

Filtre